Cheers for the coments Dom ..
I had to park right down the other end of the sea front .....I think i was almost at hastings ..... I was thinking about making the dikie seat idea but that means it will be there all the time and get in the way in the lower storage area so i am gonna use a front passenger seat with belts mounted on the frame and then use locking plate/tabs on the floor to hold it down and that way it is completely removable
Mr p .......
I got the space heater on in the cave for a while to help filler go of ...... I am not to worried about the runs in the primer as i still have a lot of blocking to do on this corner...... I did not realize how out of shape it was so i threw a bit of pimer on just to give me some idea of the shape and to seal it a bit ..... I think its not to far of now but wish i had put whole corners in had i had the cash..... .... I will be in the cave again tomorrow so more porn tomorrow nite.....

.

Afternoon all
I got a little bit more bodywork done on the van ...... Its not much but i am getting there ....I just need to get the lower half sorted and into primer .....

Well done Craig .....looking good



Feels good don't it dude popping things into primer and knowing that's all done

Well done

Mark

Vou acompanhar este projeto até o final....

Evening all
Not a lot going on in the cave at the moment apart from a ton of filler blocking and some primer being chucked around.....
So for the pervs here is some porn....

Afternoon all
Ok so i got a little jiggy with the grinder and sander yesterday and am pleased with the results....Just wish who ever repaired the side gates had only repaired the grotty bit and not covered the complete length of the gates with plate and filler as it has trapped water and rotted all the bottoms out.......Never mind i like a challenge...
Here is a little porn for you pervs ...
Before in nasty blue

Ahhhh thats so much better just need to do the insides now .....

Looking good boss






Mark

Afternoon all
Not a lot happening in the cave at the moment just a little bit of door gap correcting .......I also got the dollys out to give me door skin a good beating... ....
Here is a little porn for you pervs on this cold and horrible day.....

Coming on dude


keep going mate ...... its looking sweet Graig


Mark

Afternoon all
Not a lot happening in the cave at the moment as the weather is poo and the space heater gas aint cheap....... So i nocked myself up a wood burner from a spare gas cylinder..... Just need to fit in the cave and run a flu pipe.....
Here is the porn.....

mmmmmmmmmmmmmmmmmmmmmmmmmmmmm



all snuggley and warm in that cave mate so no excuses now


...


I have x 1 little hold to drill in Gerry for an immobiliser and it's only 4 degress and I've been putting it off for 2 weeks now

Last year I was out there in -10 ...... crazy how things change and how I've turned into a pussy



Mark

Evening all
Ok so its not a vw but its work ...... It is a 1949 chevrolet sedan delux fleetline and i have the jo of replacing the lower 6 inches
Here is a little porn for you pervs to rub ya self over christmas






I am also half way through fitting a 554ci big block ford engine in my mates willys coupe

panman wrote:Evening all
Ok so its not a vw but its work ...... It is a 1949 chevrolet sedan delux fleetline and i have the jo of replacing the lower 6 inches
Here is a little porn for you pervs to rub ya self over christmas

Nice job! it has a split screen but the wrong badge! Needs six inches taking out of the 'screen pillars , oh and have fun fitting the headers to that big block. That should keep you busy for a while. (will it give you the money to finish that panel of yours??)

Have a good one!!
Cheers,
Dom.

Evening dom...
I agree about the chevrolet needing a chop and it also needs putting on the floor but the owner likes it stock but maybe slightly lower . Its also only running a 6 cylinder motor.....As for the willys it already had a big block 490ci motor with fenderwall headers fitted but the motor had a cracked piston ring so we pulled that out and as we had pulled the 554ci motor out of his race car and sold the rolling shell it was rude not to fit it ...... I may have to copy the headers in stainless or modify the race car ones but it all seams to fit very well .... The old motor made for an interesting ride but this new motor should scare the .... out of the owner.....